Phone:  Toll Free: 800-240-1310 or Local: 770-808-0023Contact Us Site Map Home

 

 

Superior Joint Seal - #SJS-RS
2 Component - 100% Solid - Rapid Set

Floor and Wall Joint Fillers

SUPERIOR JOINT SEAL-RAPID SET is a two component, 100% solids, equal volume, elastic type epoxy. SUPERIOR JOINT SEAL-RAPID SET is formulated for quick cure at ambient temperature or overnight cure a temperatures as low as 35 deg F. SUPERIOR JOINT SEAL- RAPID SET is a soft thixotropic gel which is packaged in 22 oz. side by side dispensing cartridges.

 

Uses

Advantages

  • Filler and sealer for saw-cut control joints.
  • Flexible grout for tile and brick.
  • Moisture barrier coating.
  • Permanently flexible.
  • Easy-to-use 1:1 by volume mix ratio.
  • Excellent adhesion.
  • Self-leveling.
  • Non-sag grade is available for vertical and overhead applications.

Surface Preparation

Area must be clean and dry. Saw-cuts shall be blown clean and dry with compressed air to remove all excess moisture and debris.

 

Mixing & Application

Mix equal volumes of part A and part B. Mix thoroughly until the color is uniform, with no streaks in evidence. Be sure to scrape the sides and bottom of the mixing pail. For neat and easy application, tape both sides of joints and grooves with masking tape.

 

Apply SUPERIOR JOINT SEAL with conventional caulking gun, disposable plastic dispenser or pour from the can. Fill joints flush to the top or slightly higher than the surrounding surface. A second pass prior to curing may be necessary due to the fact that all pour grade materials will "dish" or become concave. Remove all tape and clean spills and tools immediately upon completion of installation.

 

Clean Up

Clean tools and equipment immediately with a suitable solvent such as xylene or lacquer thinner.

 

Limitations

  • Do NOT apply when temperature is below 35°F.
  • Do NOT apply to latex modified mortar or concrete.
  • Should NOT be applied when concrete is less than 5 days old.

Caution

For professional use only. Epoxy systems can cause delayed dermatitis. Avoid prolonged contact with skin. See Material Safety Data Sheet for proper handling and required safety equipment.

 

Specification

  • Packaging: 2 component cartridges, 22 oz. side by side dispensing cartridges. Other packaging available upon request.
  • Mix Ratio by Volume: 1:1
  • Color: Cement gray
  • Pot Life (100 Grams): 8-15 minutes
  • Tensile Strength: 600 psi (ASTM D-638)
  • Tensile Elongation: 100% (ASTM D-638)
  • Water Absorption: <1%
  • Shelf Life: 2 Year
  • Harness Shore A: 80 10 (ASTM D-2240)
  • Allowable Joint Movement: 10% Maximum

ESTIMATION CHART

VOLUME REQUIREMENTS FOR FILLING JOINTS
Lineal Feet Per Gallon

JOINT 1/4 1/2 3/4 1 1 1/4 1 1/2
1/4" 308.0          
1/2" 154 77.0        
3/4" 102.7 51.3 34.2      
1" 77.0 38.5 25.7 19.3    
1 1/4" 61.6 30.8 20.5 15.4 12.3  
1 1/2" 51.3 25.7 17.1 12.8 10.3 8.6
1 3/4" 44.0 22.0 14.7 11.0 8.8 7.3
2" 38.5 19.3 12.8 9.6 7.7 6.4
2 1/2" 30.8 15.4 10.3 7.7 6.2 5.1
3" 25.7 12.8 8.6 6.4 6.1 4.3
 

     

2527 Lantrac Court

Decatur Georgia GA 30035
Info@SuperiorEpoxies.com

Toll Free

Phone: 800-240-1310    Fax: 800-240-7662

Local

Phone: 770-808-0023    Fax: 770-808-6777

Copyright © 2015 - Superior Epoxies, Inc.