Phone:  Toll Free: 800-240-1310 or Local: 770-808-0023Contact Us Site Map Home

 

Superior Gloss -  Standard - Clear

SUPERIOR GLOSS (Standard): Surfaces. Available in clear.

 

Uses

Advantages

  • Excellent for use on concrete block and similar surfaces as a graffiti-resistant decorative coating.
  • With aggregate broadcast onto wet surface, produces an easy-to-clean, slip-resistant coating.
  • Tile-like coating for protecting walls and floors against water, chemicals and heavy traffic.
  • Blush-resistant, even in high humidity.
  • High gloss.
  • 100% solids.
  • Resistant to water spotting.
  • Chemical resistant

 

Caution

For professional use only. Epoxy systems can cause delayed dermatitis. Avoid prolonged contact with skin. See Material Safety Data Sheet for proper handling and required safety equipment.

 

Clean Up

Clean tools and equipment immediately with a suitable solvent such as xylene or lacquer thinner.

 

Surface Preparation

Surface must be clean, sound, dry and free of all foreign materials such as oils, grease, loose paint, dust and laitance. This may be accomplished by sand blasting or scarifying, followed by an air blast to remove dust and debris from the application area. New concrete surfaces should be acid etched, rinsed thoroughly and allowed to dry.

 

Mixing & Application

  1. Stir each component separately.
  2. Clear: Mix 2 volumes of part A with 1 volume of part B.
  3. Mix thoroughly, being sure to scrape the sides and bottom, with a strong mixing stick or slow-speed drill equipped with a paint propeller.
  4. Do not mix more than can be applied in 30 minutes.
  5. As a coating, apply mixed material by brush or roller.

For best results, two coats should be applied. Allow the first coat to cure overnight. Apply the second coat within 24 hours. If more time than 24 hours has elapsed, a light sanding of the first coat is required. SUPERIOR GLOSS can be placed as thick as desired on horizontal surfaces without affecting the cure.

 

When slip-proofing is required, broadcast sand, emery or carborundum into the first coat while still tacky. Apply the second coat to seal.

   

Limitations

  • Do NOT apply when temperature is below 50oF.
  • Do NOT apply to latex modified mortar or concrete.
  • Do NOT place over working control joint.

Specifications

  • Packaging: 3 gallon units; 15 gallon units; 150 gallon units
  • Mix Ratio by Volume: 2A: 1B
  • Color: Clear
  • Pot Life (100 Grams): 30-45 minutes
  • Tensile Strength: 3900 psi (ASTM D-638)
  • Tensile Elongation: 8% (ASTM D-638)
  • Water Absorption: 0.002
  • Shelf Life: 1 Year
  • Viscosity: 500-700 cps
  • Coverage: 160 sq. ft.
  • Cure Schedule: Initial Cure: 4-6 hours
  • Abrasion Resistance: 0.05 (ASTM D-1044) (Tabor Abrader C-10 wheel, 1000 gram load 1000 cycles)

ESTIMATION CHART

COVERAGE FOR COATING OR MEMBRANES

Thickness of Coating Applied
(1000 mils = 1 inch)
Coverage per U.S. Gallon
100% Solids System
1/4 inch = 250 mils 6.4 Square Feet
3/16 inch = 187.5 8.5 Square Feet
1/8 inch = 125mills 12.8 Square Feet
100mils 16.0 Square Feet
1/16 inch = 62.5 mils 25.5 Square Feet
50 mils 32.0 Square Feet
1/32 inch = 31.25 mils 51.0 Square Feet
20 mils 80.0 Square Feet
1/64 inch = 15.625 mils 102.0 Square Feet
10 mils 160.0 Square Feet
5 mils 320.0 Square Feet
1 mil 1600.0 Square Feet

If coating contains a solvent which will evaporate, thickness of coating
will be reduced by same percentage as solvent loss.

 

     

2527 Lantrac Court

Decatur Georgia GA 30035
Info@SuperiorEpoxies.com

Toll Free

Phone: 800-240-1310    Fax: 800-240-7662

Local

Phone: 770-808-0023    Fax: 770-808-6777

Copyright © 2015 - Superior Epoxies, Inc.