Phone:  Toll Free: 800-240-1310 or Local: 770-808-0023Contact Us Site Map Home

 

Superior Epoxy Primer - 171 - #SEP171

Low Viscosity, 100% Solids epoxy Primer

SUPERIOR EPOXY PRIMER 171 is a two component, low viscosity, 100% solids epoxy. SUPERIOR EPOXY PRIMER 171 will penetrate into concrete, sealing the surface to improve adhesion of epoxy toppings and coatings. SUPERIOR EPOXY PRIMER 171 will reduce outgassing of porous concrete to help produce pinhole free topcoats.

 

Uses

Advantages

  • Primer for porous concrete surfaces.
  • Tack coat for easier application of aggregate filled, trowel applied epoxy toppings.
  • Primer for polyester and vinyl ester toppings.
  • 100% solids, conforms to VOC regulations.
  • Low viscosity.
  • Good penetration into concrete.
  • Easy 1:1 volume mix ratio.

Surface Preparation

Surface must be clean, sound, dry and free of all foreign materials such as oils, grease, loose paint, dust and laitance. This may be accomplished by sand blasting or scarifying followed by an air blast to remove dust and debris from the application area. New concrete surfaces should be etched with a 5% muriatic acid solution or other concrete etchants, rinsed thoroughly and allowed to dry.

 

Mixing & Application Mix 1 volume of part A with 1 volume of part B. Mix thoroughly, being sure to scrape the sides and bottom with a strong mixing stick or a slow-speed drill with a paint propeller attachment. Do not mix more than can be applied in 20 minutes. Apply mixed material by brush, roller or squeegee at 150 to 200 square feet per gallon (8-10 mils). The coverage will depend upon texture of surface. Apply toppings before primer becomes tack-free, approximately 2-3 hours at 72oF.

 

Limitations

  • Do NOT apply when temperature is below 50oF.
  • Do NOT apply to latex modified mortar or concrete.

Clean Up

Clean tools and equipment immediately with a suitable solvent such as xylene or lacquer thinner.

 

Caution

For professional use only. Epoxy systems can cause delayed dermatitis. Avoid prolonged contact with skin. See Material Safety Data Sheet for proper handling and required safety equipment.

 

Specifications

  • Packaging: 2 gallon units; 10 gallon units; 110 gallon units
  • Mix Ratio by Volume: 1:1
  • Color: Clear, amber
  • Pot Life (100 Grams): 20-30 minutes
  • Viscosity: 1500 cps
  • Coverage: 160 sq. ft./gallon
  • Application Temperature: 50-90oF.
  • Solids by Weight: 100%

ESTIMATION CHART

COVERAGE FOR COATING OR MEMBRANES

Thickness of Coating Applied
(1000 mils = 1 inch)
Coverage per U.S. Gallon
100% Solids System
1/4 inch = 250 mils 6.4 Square Feet
3/16 inch = 187.5 8.5 Square Feet
1/8 inch = 125mills 12.8 Square Feet
100mils 16.0 Square Feet
1/16 inch = 62.5 mils 25.5 Square Feet
50 mils 32.0 Square Feet
1/32 inch = 31.25 mils 51.0 Square Feet
20 mils 80.0 Square Feet
1/64 inch = 15.625 mils 102.0 Square Feet
10 mils 160.0 Square Feet
5 mils 320.0 Square Feet
1 mil 1600.0 Square Feet

If coating contains a solvent which will evaporate, thickness of coating
will be reduced by same percentage as solvent loss.

 

     

2527 Lantrac Court

Decatur Georgia GA 30035
Info@SuperiorEpoxies.com

Toll Free

Phone: 800-240-1310    Fax: 800-240-7662

Local

Phone: 770-808-0023    Fax: 770-808-6777

Copyright © 2015 - Superior Epoxies, Inc.